Downlink Commands for Air Conditioner Control Parameters

This section describes the downlink commands for air conditioner control related parameters.

IR Code Learning

Name Example
trigger_infrared_learn Activate the IR learning mode.
{
  "trigger_infrared_learn": "yes"
}
infrared_learn.predefine_brand Set the preset mode as M96b (TCL/XIAOMI).
{
  "infrared_learn": {
    "predefine_brand": 1  //1: XIAOMI/TCL, 2: SHINCO/SAMSUNG/ELECTROLUX, 3: AIRWELL/BOSCH/WHIRLPOOL, 4: FUJITSU/McQUAY, 5: TRUMA
  }
}
infrared_format_code_divide Write the IR code.
{
  "infrared_format_code_divide": [
 {
    "index": 0,
    "format_code": "000006015304100400"  //9 bytes
  },
 {
    "index": 1,
    "format_code": "000000000400044410"  //9 bytes
  },
 {
    "index": 2,
    "format_code": "044000800000000000"  //9 bytes
  },
  ......
]
}
clear_infrared_format_code Clear the IR code.
{
  "clear_infrared_format_code": "yes"
}

Configure Air Conditioner System Parameters

Name Example
system_switch Turn the AC on.
{
  "system_switch": 1  //0: Off (default), 1: On
}
temperature_control_mode_enable Enable Auto and Heat mode.
{
  "temperature_control_mode_enable": {   //0: disable, 1: enable
    "heat": 1,
    "em_heat": 0,  //reserved
    "cool": 0,
    "auto": 1,
    "dehumidify": 0,
    "ventilate": 0
  }
}
temperature_control_mode.ctrl_mode Set the temperature control mode as Cool.
{
  "temperature_control_mode": {
    "ctrl_mode": 2  //0: Heat, 2: Cool, 3: Auto, 4: Dehumidification, 5: Ventilation
  }
}
target_temperature_settings Set the target temperature as 20 °C in Cool mode.
{
  "target_temperature_settings": {
    "cool": 20  //Unit: °C, range: 16-30
  }
}
Set the target temperature as 20 °C in Heat mode.
{
  "target_temperature_settings": {
    "heat": 20  //Unit: °C, range: 16-30
  }
}
target_temperature_tolerance Set the target temperature tolerance as 5 °C.
{
  "target_temperature_tolerance": {
    "target_value": 5  //Unit: °C, range: 0.1-5, default: 1
  }
}
fan_settings.fan_mode Set the fan mode as Auto.
{
  "fan_settings": {
    "fan_mode": 0  //0: Auto (default), 3: Low, 4: Medium, 5: High
  }
}
temp_control_param_config AC on, Cool mode, Auto fan mode, target temperature is 20 °C.
{
  "temp_control_param_config": {
    "on_off": 1,  //0: Off, 1: On, 255: No apply
    "temp_ctrl_mode": 2,  //0: Heat, 2: Cool, 3: Auto, 4: Dehumidification, 5: Ventilation, 255: No apply
    "fan_mode": 0,  //0: Auto, 3: Low, 4: Medium, 5: High, 255: No apply
    "target_temperature": 20  //Unit: °C, range: 16-30,32767: No apply
  }
}

Configure Open Window Detection

Name Example
window_opening_detection_settings Enable open window detection.
{
  "window_opening_detection_settings": {
    "enable": 1  //0: Disable (default), 1: Enable
  }
}
Set the temperature change as 10 °C/min.
{
  "window_opening_detection_settings": {
    "difference_in_temperature": 10  //Unit: °C/min, range: 1-10, default: 3
  }
}
Set the stop temperature time as 360 minutes.
{
  "window_opening_detection_settings": {
    "stop_time": 360  //Unit: min, range: 1-1440, default: 30
  }
}
open_window_alarm Trigger the open window alarm.
{
  "open_window_alarm": {
    "mode": 1  //0: Release, 1: Alarm
  }
}

Configure Filter Cleaning Alarm

Name Example
filter_clean_settings Enable the filter cleaning alarm.
{
  "filter_clean_settings": {
    "enable": 1  //0: Disable (default), 1: Enable
  }
}
Set the reminder interval as 1 day.
{
  "filter_clean_settings": {
    "reminder_period": 1  //Unit: day, range: 1-730, default: 90
  }
}
filter_clean_alarm Trigger the filter cleaning alarm.
{
  "filter_clean_alarm": {
    "mode": 1  //0: Release, 1: Alarm
  }
}

Configure Schedule Parameters

Tip: To delete a plan, just leave the value of the command as all 0.
Name Example
schedule_settings Enable/Add plan 4.
{
  "schedule_settings": [
    {
      "id": 3,  //Schedule ID, range: 0-7
      "enable": 1  //0: Disable (default), 1: Enable
    }
  ]
}
Schedule name is Schedule 1.
{
  "schedule_settings": [
    {
      "id": 0,  //Schedule ID, range: 0-7
      "name1": "schedu",  //First 6 characters
      "name2": "le 1"  //Last 4 charatersI
    }
  ]
}
Schedule 1 fan mode is Auto and target temperature is 16 °C.
{
  "schedule_settings": [
    {
      "id": 0,  //Schedule ID, range: 0-7
      "fan_mode": 0,  //0: Auto, 3: Low, 4: Medium, 5: High
      "target_temp": 16  //Unit: °C, range: 16-30
    }
  ]
}
Schedule 1 AC on in Cool mode.
{
  "schedule_settings": [
    {
      "id": 0,  //Schedule ID, range: 0-7
      "switch_on": 1,  //0: Off, 1: On
      "work_mode": 2  //0: Heat, 2: Cool, 3: Auto, 4: Dehumidification, 5: Ventilation
    }
  ]
}
Enable schedule time 1, time is 8:00, repeat day is Mon., Wed., Fri.
{
  "schedule_settings": [
    {
      "id": 0,  //Schedule ID, range: 0-7
      "cycle_settings": [
        {
          "id": 0,  //Time ID, range: 0-15
          "enable": 1,  //0: Disable (default), 1: Enable
          "execution_time_point": 480,  //Unit: min, range: 0-1439
          "execution_day_sun": 0,  //0: Disable, 1: Enable
          "execution_day_mon": 1,  //0: Disable, 1: Enable
          "execution_day_tues": 0,  //0: Disable, 1: Enable
          "execution_day_wed": 1,  //0: Disable, 1: Enable
          "execution_day_thu": 0,  //0: Disable, 1: Enable
          "execution_day_fri": 1,  //0: Disable, 1: Enable
          "execution_day_sat": 0,  //0: Disable, 1: Enable
          "reserved": 1
        }
      ]
    }
  ]
}
insert_temporary_plan Execute plan 1.
{
  "insert_temporary_plan": {
    "id": 0  //0-15, 255: Stop insertion
  }
}
delete_task_plan Delete plan 2.
{
  "delete_task_plan": {
    "type": 1  //0-15, 255: Reset all
  }
}

Configure Energy Saving Parameters

Tip: To delete a task, just leave the value of the command as all 0.
Name Example
temperature_limit_task_settings Enable the temp limit task.
{
  "temperature_limit_task_settings": [
    {
      "id": 0,  //Task ID, range: 0
      "enable": 1  //0: Disable (default), 1: Enable
    }
  ]
}
Valid date is 1.1 to 12.31.
{
  "temperature_limit_task_settings": [
    {
      "id": 0,
      "task_date_settings": {
        "start_mon": 1,  //Range: 1-12
        "start_day": 1,  //Range: 1-31
        "end_mon": 12,  //Range: 1-12
        "end_day": 31  //Range: 1-31
      }
    }
  ]
}
Active period is 8:00 to 18:00.
{
  "temperature_limit_task_settings": [
    {
      "id": 0,
      "execute_period": {
        "start_minute": 480,  //Unit: min, range: 0-1439
        "end_minute": 1080  //Unit: min, range: 0-1439
      }
    }
  ]
}
Repeat cycle is Mon., Wed., Fri.
{
  "temperature_limit_task_settings": [
    {
      "id": 0,
      "cycle_settings": {
        "execution_day_sun": 0,  //0: Disable, 1: Enable
        "execution_day_mon": 1,  //0: Disable, 1: Enable
        "execution_day_tues": 0,  //0: Disable, 1: Enable
        "execution_day_wed": 1,  //0: Disable, 1: Enable
        "execution_day_thu": 0,  //0: Disable, 1: Enable
        "execution_day_fri": 1,  //0: Disable, 1: Enable
        "execution_day_sat": 0  //0: Disable, 1: Enable
      }
    }
  ]
}
Low threshold is 16 °C.
{
  "temperature_limit_task_settings": [
    {
      "id": 0,
      "low_threshold": 16  //Unit: °C, range: 16-30
    }
  ]
}
High threshold is 30 °C.
{
  "temperature_limit_task_settings": [
    {
      "id": 0,
      "high_threshold": 30  //Unit: °C, range: 16-30
    }
  ]
}
delete_temperature_limit_task Delete the temp limit task.
{
  "delete_temperature_limit_task": {
    "type": 0  //0: Task 1
  }
}
vacation_task_settings Add/Enable task 1.
{
  "vacation_task_settings": [
    {
      "id": 0,  //Task ID, range: 0-7
      "enable": 1  //0: Disable (default), 1: Enable
    }
  ]
}
Task 1 valid date is 1.1 to 12.31.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "task_date_settings": {
        "start_mon": 1,  //Range: 1-12
        "start_day": 1,  //Range: 1-31
        "end_mon": 12,  //Range: 1-12
        "end_day": 31  //Range: 1-31
      }
    }
  ]
}
Task 1 active period is 8:00 to 18:00.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "execute_period": {
        "start_minute": 480,  //Unit: min, range: 0-1439
        "end_minute": 1080  //Unit: min, range: 0-1439
      }
    }
  ]
}
Task 1 repeat cycle is Mon., Wed., Fri.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "cycle_settings": {
        "execution_day_sun": 0,  //0: Disable, 1: Enable
        "execution_day_mon": 1,  //0: Disable, 1: Enable
        "execution_day_tues": 0,  //0: Disable, 1: Enable
        "execution_day_wed": 1,  //0: Disable, 1: Enable
        "execution_day_thu": 0,  //0: Disable, 1: Enable
        "execution_day_fri": 1,  //0: Disable, 1: Enable
        "execution_day_sat": 0  //0: Disable, 1: Enable
      }
    }
  ]
}
Task 1 fan mode is Auto.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "fan_mode": 0  //0: Auto, 3: Low, 4: Medium, 5: High
    }
  ]
}
Task 1 target temperature is 16 °C.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "target_temp": 16  //Unit: °C, range: 16-30
    }
  ]
}
Task 1 AC on.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "switch_on": 1  //0: Off, 1: On
    }
  ]
}
Task 1 cool mode.
{
  "vacation_task_settings": [
    {
      "id": 0,
      "work_mode": 2  //0: Heat, 2: Cool, 3: Auto, 4: Dehumidification, 5: Ventilation
    }
  ]
}
delete_vacation_task Delete holiday mode task 1.
{
  "delete_vacation_task": {
    "type": 0  //0-7, 255: Reset all
  }
}